I found that riffle's operating voltage is 3.3v, while most of sensors compatible with Arduino is...
Public Lab is an open community which collaboratively develops accessible, open source, Do-It-Yourself technologies for investigating local environmental health and justice issues.
If you cannot use the ReCaptcha to verify you are not a bot, use this alternative verification.
or sign up to join the Public Lab community
Forgotten or lost your password? Reset it by clicking here
shanlter asked on November 04, 2017 16:01
213 views | 2 answers | #15150
I found that riffle's operating voltage is 3.3v, while most of sensors compatible with Arduino is 5V.
How could riffle compatible with those sensors?
That's a good question. There is no 5V-out pin on the Riffle, but there is a "VBAT" pin on the 2x7 pin header. I assume that pin carries the voltage of the battery that powers the Riffle. The Riffle can be powered by batteries with 3.5 to 6 volts. If you use a 5V to 6V battery, the VBAT pin should supply about 5V. I don't know if this current is regulated.
Evidence suggests my answer is wrong. I powered a Riffle with a battery pack which supplied 4.5V, but the VBAT pin supplied only 2.3V. So maybe it's not so easy to power 5V sensors with a Riffle.
Further empirical evidence suggests that the VBAT pin delivers the voltage of the battery that is plugged into the "Lithium 3.7V" connector, but not the "General 3.5-6V" connector. So the VBAT pin does not supply 5 volts when a 5 volt battery is plugged into the proper connector. I assume that means that additional electronics are generally required to use sensors which require 5V.
However, there might be a simpler workaround for some sensors. I have used the Modern Device wind sensor Rev P with a 5V Arduino Nano. The wind sensor requires 8V which the Nano does not supply. So I powered the Nano with a 9V battery and powered the wind sensor from the "VIN" pin which is where the battery connects to the Nano. Everything else was wired normally. It has worked well on several flights (https://publiclab.org/tag/series:diy-wind-sensors).
I don't know whether the Riffle could tolerate the logic signals sent back from a sensor that is powered with 5V. It probably depends on the sensor, some of which might use 3.3V logic.
Although there are sensors that require more than 3.3V, most of the simple DIY sensors are designed to use 3.3V. For example, all of the sensors here can use 3.3V, and some can use either 3.3V or 5V.
It is a common design decision to use only 3.3V and allows better longevity on battery power. This is also a characteristic of the Arduino Pro Mini, several other Arduinos, and the Adafruit Feather boards.
Thanks very much! The link of your website is very helpful! I will try when I receive a riffle : )
Reply to this comment...
Log in to comment
Hallo! If the hardware is Riffle version 0.1.8, the relevant schematic is here -- and, so far as I can tell, VBAT should simply be the battery input voltage. But I'm also very hesitant to bet against diagnostic performed by the generally-very-thorough @cfastie, so I suspect I'm missing something.
In any case: getting a Riffle (which does indeed operate at 3.3V) to talk to 5V sensors will require two things vis-a-vis power: a) you'll need to find a way to provide 5V to power the sensor, and b) you'll need to find a way to talk to the sensor with compatible signal levels. If, e.g., the 5V sensor outputs an analog signal that ranges from 0..5V, the Riffle's analog inputs can only handle 0..3.3V, so you'll want to use a voltage-divider (easy way) or a 'level-shifter' (a special chip that lets different voltage levels speak to one another). Another examples: if e.g., the 5V sensor uses the i2C protocol, there's the possibility that the Riffle's digital 3.3V signal HIGH values (3.3V) aren't high enough to register as a 'HIGH' for the i2c sensor chip in question -- a case that might also be handled with a level-shifter, I think.
For a nice general discussion of getting 3.3V hardware to talk to 5V hardware, see this post by Hackaday.
Hi Dan, thanks very much! So basically, what I need is to connect (at least) DO and pH sensors to Riffle. My collaborator said that using a voltage - divider will affect the data inaccuracy. I haven't try yet, but I think I will when I get a riffle and get back home.
How can we connect a PMS5003 dust sensor to an Arduino?
updated 6 months ago
What probes to get with data loggers?
updated 10 months ago
Is the Riffle for sale at the Public Lab Store?
updated about 1 year ago
How much of an Arduino's onboard memory would be available for datalogging?
updated over 1 year ago
How similar is the code for the KnowFlow and the RIFFLE data loggers?
updated over 1 year ago
Seeking DC-area folks interested in building temperature sensors for urban heat island measurement
updated almost 2 years ago
What are ways to record ambient temperature every 5 sec and export easily?
How do I install a bootloader on a Riffle data logger?
updated almost 2 years ago